Презентация на тему Physical Output

Arduino
Servo-motors
Rotary actuator that allows for precise control of angular

position
DC-motors
Converts direct current electrical power into mechanical power
Stepper-motors
Divides a full rotation into a number of equal steps

to brushes (contacts)
Control the magnetic field of the coils
Drives

a metallic core (armature)
Direction of rotation can be reversed by reversing the polarity
Require a transistor to provide adequate current
Primary characteristic in selecting a motor is torque
How much work the motor can do

size
Three phases of driving coils
Require more complicated electronic control
Electronics

speed controllers

or not
Voltage – what voltage it best operates at
Current

(efficiency) – how much current it needs to spin
Speed – how fast it spins
Torque – how strong it spins
Size, shaft diameter, shaft length

draw a lot more current, up to 10x more
If

you “stall” them (make it so they can’t turn), they also draw a lot of current
They can operate in either direction, by switching voltage polarity
Usually spin very fast: >1000 RPM
To get slower spinning, need gearing

higher the voltage, the faster the spinning
Polarity determines which

way it rotates



Can be used as voltage generators

little signals
Since motors can act like generators,
Need to prevent

them from generating “kickback” into the circuit
Can control speed of motor with analogWrite()

int switchPin = 2;
void setup() {
pinMode(switchPin, INPUT);

pinMode(motorPin, OUTPUT);
}
void loop() {
digitalWrite(motorPin, digitalRead(switchPin));
}

int potPin = A0;
void setup() {
}
void loop() {

int spd = analogRead(potPin);
spd = map(spd, 0, 1023, 0, 255);
analogWrite(motorPin, spd);
}

instead of continuously rotating
Rotate over a range of 0

to 180 degrees
Motor driver is built into the servo
Small motor connected through gears
Output shaft drives a servo arm
Connected to a potentiometer to provide position feedback
Continuous rotation servos
Positional feedback disconnected
Rotate continuously clockwise and counter clockwise with some control over the speed

pulse
Short pulse of 1 ms will cause to rotate

to one extreme
Pulse of 2 ms will rotate the servo to the other extreme

Servos require pulses different from the PWM output from analogWrite

3-wire interface
Servos are spec’d by:
weight: 9g
speed: .12s/60deg @ 6V
torque:

22oz/1.5kg @ 6V
voltage: 4.6~6V
size: 21x11x28 mm

20 millisecs)
Pulse width ranges from 1 to 2 millisecs
In

practice, pulse range can range from 500 to 2500 microsecs

potPin = A0;
const int pulsePeriod = 20000; //us
void setup()

{
pinMode(servoPin, OUTPUT);
}
void loop() {
int hiTime = map(analogRead(potPin), 0, 1023, 600, 2500);
int loTime = pulsePeriod - hiTime;
digitalWrite(servoPin, HIGH); delayMicroseconds(hiTime);
digitalWrite(servoPin, LOW); delayMicroseconds(loTime);
}

the servo
pin- the pin number that the servo is

attached to
min (optional) - the pulse width, in microseconds, corresponding to the minimum (0-degree) angle on the servo (defaults to 544)
max (optional) - the pulse width, in microseconds, corresponding to the maximum (180-degree) angle on the servo (defaults to 2,400)
servo.write(angle) – turn the servo arm
angle – the degree value to write to the servo (from 0 to 180)

to control a servo
int angle = 0; // variable

to store the servo position
void setup(){
myservo.attach(9); // attaches the servo on pin 9 to the servo object
}
void loop(){
for(angle = 0; angle < 180; angle += 1){ // goes from 0 degrees to 180
myservo.write(angle); //tell servo to go to position in variable 'angle'
delay(20); // waits 20ms between servo commands
}
for(angle = 180; angle >= 1; angle -= 1){ // goes from 180 degrees to 0
myservo.write(angle);
delay(20);
}
}

servo object to control a servo
int potpin = 0;

// analog pin used to connect the potentiometer
int val; // variable to read the value from the analog pin
void setup(){
myservo.attach(9); // attaches the servo on pin 9 to the servo object
}
void loop(){
val = analogRead(potpin); // reads the value of the potentiometer
val = map(val, 0, 1023, 0, 180); // scale it to use it with the servo
myservo.write(val); // sets position
delay(15);
}

response to control pulses
Number of degrees for a step

is motor-dependent
Ranging from one or two degrees per step to 30 degrees or more
Two types of steppers
Bipolar - typically with four leads attached to two coils
Unipolar - five or six leads attached to two coils
Additional wires in a unipolar stepper are internally connected to the center of the coils

the same way
Single "common" lead, will always be negative.

The other lead will always be positive
Disadvantage - less available torque, because only half of the coils can be energized at a time
Bipolar drivers work by alternating the polarity to phases
All the coils can be put to work

tied together internally and brought out as a 5th

wire. This motor can only be driven as a unipolar motor.

This motor only joins the common wires of 2 paired phases. These two wires can be joined to create a 5-wire unipolar motor. Or you just can ignore them and treat it like a bipolar motor!

It can be driven in several ways:
4-phase unipolar - All the common wires are connected together - just like a 5-wire motor.
2-phase series bipolar - The phases are connected in series - just like a 6-wire motor.
2-phase parallel bipolar - The phases are connected in parallel. This results in half the resistance and inductance - but requires twice the current to drive. The advantage of this wiring is higher torque and top speed.

{2, 3, 4, 5};
int delayTime = 5;
void setup() {

for(int i=0; i<4; i++)
pinMode(stepperPins[i], OUTPUT);
}

void loop() {
digitalWrite(stepperPins[0], HIGH);
digitalWrite(stepperPins[1], LOW);
digitalWrite(stepperPins[2], LOW);
digitalWrite(stepperPins[3], LOW);
delay(delayTime);
digitalWrite(stepperPins[0], LOW);
digitalWrite(stepperPins[1], HIGH);
digitalWrite(stepperPins[2], LOW);
digitalWrite(stepperPins[3], LOW);
delay(delayTime);
digitalWrite(stepperPins[0], LOW);
digitalWrite(stepperPins[1], LOW);
digitalWrite(stepperPins[2], HIGH);
digitalWrite(stepperPins[3], LOW);
delay(delayTime);
digitalWrite(stepperPins[0], LOW);
digitalWrite(stepperPins[1], LOW);
digitalWrite(stepperPins[2], LOW);
digitalWrite(stepperPins[3], HIGH);
delay(delayTime);
}

{2, 3, 4, 5};
int delayTime = 5;
void setup() {

for(int i=0; i<4; i++)
pinMode(stepperPins[i], OUTPUT);
}
void loop() {
digitalWrite(stepperPins[0], LOW);
digitalWrite(stepperPins[1], HIGH);
digitalWrite(stepperPins[2], HIGH);
digitalWrite(stepperPins[3], LOW);
delay(delayTime);
digitalWrite(stepperPins[0], LOW);
digitalWrite(stepperPins[1], HIGH);
digitalWrite(stepperPins[2], LOW);
digitalWrite(stepperPins[3], HIGH);
delay(delayTime);
digitalWrite(stepperPins[0], HIGH);
digitalWrite(stepperPins[1], LOW);
digitalWrite(stepperPins[2], LOW);
digitalWrite(stepperPins[3], HIGH);
delay(delayTime);
digitalWrite(stepperPins[0], HIGH);
digitalWrite(stepperPins[1], LOW);
digitalWrite(stepperPins[2], HIGH);
digitalWrite(stepperPins[3], LOW);
delay(delayTime);
}

stepper motors
stepper(steps, pin1, pin2, pin3, pin4) – attach and

initialize stepper
steps: number of steps in one revolution of motor
pin1, pin2, pin3, pin4: 4 pins attached to the motor
setSpeed(rpms) - Sets the motor speed in rotations per minute (RPMs)
step(steps) - Turns the motor a specific number of steps, positive to turn one direction, negative to turn the other
This function is blocking
wait until the motor has finished moving before passing control to the next line in sketch