Презентация на тему iPECS SMB eMG Expansion (iPECS SMBSW-TRA-01-023)

Rights Reserved
This material is copyrighted by Ericsson-LG Enterprise Co.

Ltd. Any unauthorized reproductions, use or disclosure of this material, or any part there of, is strictly prohibited and is a violation of Copyright Laws. Ericsson-LG Enterprise reserves the right to make changes in specifications at any time without notice. The information furnished by Ericsson-LG in this material is believed to be accurate and reliable, but is not warranted to be true in all cases.
Ericsson-LG and iPECS are trademarks of Ericsson-LG Enterprise Co. Ltd.

connection is connected by TDM link.


eMG80 Exp
Master
Configuration
eMG80 Expansion (eMG80E)


eMG80

Exp
Slave

TDM link

Ethernet Switch

WTIB should be installed in master system (not in slave)
One PRIB/BRIB line should be connected to master system if PRIB/BRIB is used in slave system.
IP device (IP phone, UCS client, iPCR, Application) & VOIP trunk is need to be installed in master.
Could you use expansion slave system to expand TDM port (DTIB/SLIB/LCOB/BRIB/PRIB etc.)

should be installed)
eMG80 Master system Configuration
eMG80 Expansion (eMG80E)

slave system.
The “total number of

port” should be lager than CCM attribute of eMG80 slave system.

eMG80 Master Site Configuration

eMG80 Expansion (eMG80E)

system(eMG80-EXPS license should be installed)
All station

and CO device will be registered to master system and license will be
checked in master if eMG80N-EXPS license is used.
if Temp license is used then TNET should be enabled for all device in PGM 132.
TNET should be enabled for other device (not station and CO line) in PGM 132.

eMG80 Expansion (eMG80E)

slave system and total number of port that can

be registered to master.

eMG80 slave system Configuration

eMG80 Expansion (eMG80E)

Expansion


eMG800 (LCM)
Slave
VOIB
Ethernet Switch
WTIB should be installed in master system

(not in slave)
IP device (IP phone, UCS client, iPCR, Application) & VOIP trunk is need to be installed in master.
Could you use expansion slave system to expand TDM port (DTIB/SLIB/LCOB/BRIB/PRIB etc.)

should be installed)
eMG800 Master system Configuration
eMG800 Expansion

Master Site Configuration
eMG800 Expansion

slave system.
The “total number of

port” should be lager than CCM attribute of eMG800
slave system.
Assign zone number for slave system (eg, 2)

eMG800 Master Site Configuration

eMG800 Expansion

system(eMG800-EXPS license should be installed)
All station

and CO device will be registered to master system and license will be
checked in master if eMG800-EXPS license is used.
if Temp license is used then TNET should be enabled for all device in PGM 132.
TNET should be enabled for other device (not station and CO line) in PGM 132.

eMG800 Expansion

slave system and total number of port that can

be registered to master.
Assign zone number for master system (eg, 1)

eMG800 slave system Configuration

eMG800 Expansion

VMIB slot number for zone 1
eg, 19 is VOIB

slot number and 21 is VMIB slot number of master(zone 1)

eMG800 Expansion

Assign VOIB and VMIB slot number for zone 2
eg, 29 is VOIB slot number and 30 is VMIB slot number of slave(zone 2)

number of TDM port of eMG800.
Assign two RTP relay

deice for inter zone in PGM 441
eg, 19 is VOIB slot number of master(zone 1), 29 is VOIB slot number of slave(zone2)

LCM server 1
(eMG800)

VOIB

ZONE 1

CCM server 1
(eMG800)

VOIB

VOIB

eMG800 Expansion

Slot 19

Slot 29

Assign VOIB for inter zone (1 <-> 2)